The two main types of shower trays are the traditional chunky shape with wide rims and low profile trays which are usually around 40mm or less in height.
Because low-profile trays have a sleek and sophisticated look, the vast majority of bathroom showrooms and catalogs feature them in their layouts.
Having a low-profile tray gives the impression of more space in the room, plus it’s more convenient not having to take a step into the shower.
If so, can everyone get a low spec tray? Simply put, the answer is both yes and no. Everyone is allowed to have a tray, but only some people can secure it directly to the floor.
It is possible to install low-profile trays only in situations where there is access to proper drainage and where the drainage runs between the floor joists. It’s not a good idea to start drilling holes in your joists to accommodate drainage pipes to run over the joists. This can cause serious structural damage.
Low profile shower tray installation
The process of installing a low-profile shower tray is a little different than a regular model and can be challenging in some cases. Here we have provided a quick five-step guide for DIY fans.
Step 1: Check the subfloor. Before starting, make sure the tray can be supported by the floor it is placed on. It should be completely rigid and not flexible as it may lead to problems. Replace each floor in this area with marine plywood that is at least 18mm thick and mark where the tray will be.
Step 2. Cut an access hatch To access the waste, you will need to cut an access hatch in the floorboards near the tray. The best tool for this is a jigsaw because it allows you to cut more precisely.
Step 3. Cut a waste hole For the waste of the shower tray, a hole will also need to be made, so take accurate measurements and carefully start creating the necessary space. Once this is done, you can proceed with the construction of the dump itself.
Step 4: Apply Mortar Now it’s all going to get a little messy! Make a mortar by mixing 5 parts construction sand with 1 part cement. Spread this mortar in a thin layer on the space under the tray.
Before using the leveler, press the tray lightly on the mortar to make sure everything is as it should be. Once you are satisfied, give the mortar 24 hours to dry.
Step 5. Connect and seal the outlet pipe Connect the waste trap and the outlet pipe using the valve you created earlier (you can use it later if you need maintenance) Now you can Sealing the edges of the tray with it, complete the process. Silicone sealant
Low profile shower tray problems
Low-profile shower trays, although modern and stylish, are not perfect, and a low-profile shower tray can have problems, the most important of which is overflow. Why do low profile showers tend to overflow? What makes them different from each other? Shower trays with low profile have a height of about 40 mm. The most important factor in their fame was the sophisticated appearance of their products. In addition, it gives the impression that your bathroom is larger and more sophisticated.
On the other hand, a low-profile shower tray may present a number of challenges. For starters, a properly functioning shower tray should empty faster than it collects water. On the other hand, if your drainage system is not very good, this may be the problem for you.
For starters, a low-profile shower tray has a limited capacity for the amount of water it can hold. Therefore, drainage must be particularly effective to prevent water accumulation.
As a result, there should be a significant amount of drainage space under the tray as well as existing joists. In general, a low-profile tray should have very effective drainage. This is a requirement.
In addition, the trap must be wide enough. Once this condition is met, the shower tray will function as intended. At this point, we are aware of the issue with the low profile shower tray. So, let’s take a look at the answer, shall we?
Taking a quick shower is an easy and effective solution to this problem. This not only prevents water from spilling, but also prevents the wire from overheating in the bathroom.
Jt fusion shower tray
JT stands for Just Tray, as the name suggests they specialize in shower trays and use the latest tray technology. JT is the UK’s number one shower tray manufacturer, founded thirty years ago in Leeds, West Yorkshire.
The JT fusion is one of the most popular JT models and comes in a variety of sizes and shapes, and we’re going to give you some of those specs. The extensive JT Fusion range is now available in 47 sizes and 19 of these sizes are offered with an integrated tiling option.
Foundations to provide a watertight enclosure, whether new installation or already in place.
This stunning product can also be purchased with brand new hidden scraps that give it a more modern and understated look.
The JT FUSION is available to buy on many websites if you’re not buying from the UK, but otherwise why go anywhere but JT themselves. Here are some of the features of JT Fusion:
48 sizes are available. To Square, rectangular, quarter and offset quarter faces are offered. Mounts on the floor or on legs with the JT Fusion Riser Kit.
Easy-to-fit bases allow for faster installation. It contains JT90mm scraps for tiling, it can be purchased in increments of 13mm.
25-year warranty
JT fusion features JT anti-skid. 9 different color options are available for JT Fusion, including the distinctive colors of Sage Green, Mistral Grey, Malbec Red, Pastel Blue, Astro Black, Astro White, Astro Slate, Astro Sand and Matt/glossy white.
JT Fusion shower trays are available in various sizes for every shape, from the smallest square model with dimensions of 700×700 mm to the largest rectangular models with dimensions of 1800×800 mm.
JT fusion shower tray installation
Installing the JT Fusion shower tray is not difficult and its installation steps are not much different from other shower trays. However, there are some small details to consider before starting the installation:
Make sure the enclosure measurements match the shower base, check for product defects or damage that may have occurred in transit.
Accepting the quality of the product shows that it meets your needs. Unless these specific instructions are followed, none of the warranties are fulfilled.
When installing in combination with a steamer, you must ensure that the steam outlet is at a height of at least 300mm from the top of the tray.
Non-slip trays cannot be used in steam cabins due to compatibility issues. Keep in good condition.
The shower tray should be cleaned frequently with a damp sponge or cloth and then dried with a soft cloth. If necessary, use a non-abrasive cleaner to get rid of stubborn stains.
The installation instructions for the flat to floor and tall shoe tray made by JT can be found on their website in an easy to access PDF file and can be found in less than a minute with a simple search. The instructions are brief, but accompanied by pictures to add visual aid and help you understand the steps more easily. As mentioned earlier, failure to do so will void the warranty, so we still recommend that you seek the help of a professional plumber.
JT fusion shower tray reviews
In this section, we’re going to review some of what customers have to say about their JT shower tray. Although Google does not verify these reviews, the search engine reviews reports of fake reviews and identities and removes them. Debbie Ridgway said: “It had a faulty shower tray that cracked after 3 years. Spoke with Ryan very efficiently and offered to replace the unit. Excellent customer service.” And gave five stars
While PAWEL said I have tried to get replacements for the shower waste and contacted Just Trays directly. I was completely ignored. If you decide to buy from them, be aware that if you need replacement parts, you’ll probably have to rip the tray out and install a new one.
The drains are just trays, so you won’t find any spares to fit them. Do yourself a favor and go with Matki or another reputable brand, you’ll save a fortune.
Just Trays are completely unprofessional and there is no after sales customer service. I would give 0 stars if possible… Update: After posting a negative review here, Just Trays finally got back to me and my issue was resolved quickly and for free.
I just wish I didn’t have to use this site to get any answers. In the end, my problem was solved, but still, I’m left with the impression that if it wasn’t for the negative feedback, it probably wouldn’t have existed. Use at your own risk.”
And gave 1 star. The JT shower tray, like any product, had many positive and negative reviews and unfortunately, no professional review was provided on any website (we have also looked at it), but the positive thing is that the JT shower trays all have twenty-five pieces. – Warranty year
P shaped shower tray
The p-shaped shower part does exist but it’s not exactly a shower tray and is more commonly known as a p-shower bath, after all when you have a large p-shaped shower in your bathroom it may also double as a bathtub. .
Due to its many advantages, the p-shaped shower bath is one of the types of tubs that can be wonderful. Many people are not sure which to choose between a bathtub and a shower due to the increasing popularity of showers over bathtubs.
Most people struggle with lack of room and are unable to accommodate both facilities. Although both are great, they have different benefits.
According to our previous discussion, the P shape was a technique to help people choose between a bath and a shower. It combines the two functions below is a list of important features common to all p-shaped tubs:
Occupy less space: The first advantage of a shower bath is that it can help you make better use of your bathroom space. It is possible to include a shower and other bathroom facilities in one unit.
There is no need for additional or separate space for any of them. Despite their size, small bathrooms usually have limited space. In such a situation, it may be a good choice to do so.
Less money needed: Cheaper costs, both in terms of unit and installation, are another compelling argument in favor of installation.
From Since the shower and tub are combined into one unit, you will save money that you would have otherwise spent on a separate shower and tub.
